View AFE2000-26S48NA_669991.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

AFE2000 SERIES
Single output
* Approved to EN61000, IEC-1000, UL1950, CSA 22.2 No. 950-95 * Operating ambient temperature of 0C to +50C * Complies with ETS300 132-1 and EN61000-3-2 * Hot-swap capability * 11.5 x 6.75 x 4.9 inch size * N+1 redundancy capability * Extensive features available * Compatible with AFS standard shelves for configuring rack-mounted power systems
The AFE2000 power module is a rack mountable single phase AC to DC power supply, designed to be a cost-competitive front-end power supply for distributed power systems. It is particularly suitable for use in data processing, datacom and telecom applications. The outputs are floating so the end user can ground the plus, minus or neither depending on the end use application. The AFE2000 power modules are designed for hot-swap operation and can be mounted into AFS4000/6000 power shelves for redundant-mode operation. [ 2 YEAR WARRANTY ]
SPECIFICATION
OUTPUT SPECIFICATIONS Output voltage Output power Regulation Turn-on
All specifications are typical at nominal input, full load at 25C unless otherwise stated EMC CHARACTERISTICS 1.0% 1.0% 2000W 12W 3.0% Conducted emissions Radiated emissions Immunity - conducted Immunity - radiated Immunity - ESD Line harmonics FCC-CFR, part 15, subpart B Class B CISPR 22 Class B FCC-CFR, part 15, subpart B (Note 7) CISPR 22 (Note 7) IEC1000-6 Level 2 IEC1000-3 Level 3 IEC1000-2 Level 3 per EN61000-3-2 Compliant
Main: 48/54.5/56.2VDC Auxiliary: 12VDC Main Auxiliary Line, load, IT, ageing
Output rise time 100 to 400ms Turn-on (AC applied) 4s max. Turn-on (inhibit removed) 1.5s max. 480mV pk-pk 100 to 3kHz 35dBrnC 60VDC max. Delivers full power Latch-off Automatic recovery Latch-off 10%
GENERAL SPECIFICATIONS Hold-up time (See Note 1) Efficiency Isolation voltage Input/output Input/chassis Output/chassis 150 to 170VAC 0 to 150VAC 500ms 20ms 86% 3000VAC 1500VAC 100VAC 200kHz EN60950, IEC950, UL1950 CSA C22.2 No. 950 Electrolytic zinc coated CRS, ASTM A591, light beige paint 5.0kg (11Ibs) MIL-HDBK-217E Demonstrated 150,000 hours 300,000 hours
Ripple and noise (<50MHz) Transmission noise Overvoltage protection Undervoltage protection >44.5VDC <42VDC for >5s Short circuit protection Current sharing Remote sense INPUT SPECIFICATIONS Input voltage range Input frequency range Input surge current Safety ground leakage current Input current Power factor 200/240VAC nom. 50/60Hz nom. 25C cold start 254VAC @ 60Hz 220VAC, 2000W <30s >30s
Switching frequency Approvals and standards Case material Weight
Active current share (50% to 100% loading)
1.0V max. distribution line loss MTBF
170 to 264VAC 47Hz to 63Hz 22A 1.5mA max. 0.5mA typ. 10.5A rms 0.99 min.
ENVIRONMENTAL SPECIFICATIONS Thermal performance Cooling Relative humidity Altitude Vibration Shock Operating Operating 5Hz to 500Hz Operating ambient Non-operating 0C to +50C -40C to +100C Forced air 5% to 95% RH 13,000 feet max. 0.75G rms peak 15G, 1/2 Sine, 11ms
PAGE 1
DISTRIBUTED POWER FRONT END AC/DC POWER SUPPLIES
|
2000W AC/DC
2000 Watt AC/DC PFC front-end for distributed power architectures
OUTPUT VOLTAGE 48VDC 54.5VDC 56.2VDC OUTPUT CURRENT RIPPLE MIN 0A 0A 0A MAX 41.7A 36.7A 35.6A 480mV 545mV 562mV TOTAL REGULATION 3.0% 3.0% 3.0% REMOTE ENABLE/INHIBIT Inhibit Inhibit Inhibit PARALLEL INTERFACES All All All AFE2000-26S48NA AFE2000-26S54NA AFE2000-26S56NA MODEL NUMBER
Parallel interface specifications.
All signals are referenced to ISO_GND unless otherwise indicated. Isolated signal ground (ISO_GND) May be connected to any voltage in the range from +Vout+5VDC to -Vout5VDC. Overtemperature (OTW) Output bi-level signal. Bi-level signals are open-collector (drain) with a 5mA sink capability and maximum voltage stand-off of 60VDC. Logic 0 : Signal precedes OT shutdown by 5ms. Logic 1 : Normal operation. Remote Inhibit (INHIBIT) Input bi-level signals. Bi-level input signals shall be no greater than 5VDC. Logic 0 : Normal operation. Logic 1 : Output inhibit. Voltage margin down (DOWN) Input bi-level signals. Bi-level input signals shall be no greater than 5VDC. Logic 0 : Nominal output voltage. Logic 1 : 44.5 to 45.5VDC output. Power good signal (PWR_GOOD) Output bi-level signal. Bi-level signals are open-collector (drain) with a 5mA sink capability and maximum voltage stand-off of 60VDC. Logic 0 : Output undervoltage. Logic 1 : Output voltage normal. Fault fail signal (F/F ) Differential relay contact, isolated from all outputs and returns within the power module. Relay closed : Power supply failure Relay open : Normal operation. Power fail warning signal (PFW) Output bi-level signal. Bi-level signals are open-collector (drain) with a 5mA sink capability and maximum voltage stand-off of 60VDC. Logic 0 : Signal precedes loss of output power by 5ms. Logic 1 : Normal operation. Module Missing Pin (MM) Provision for detection of unseated or removed module. MM pins are common internal to the power supply. Internal pull-up resistor to +5VDC logic bias, referenced to RS-. Auxiliary Output (AUX ) 12VDC auxiliary output. Isolated from both the main output and the isolated signal ground. May be utilized for external housekeeping supply and connected to either main output or isolated signal ground. Current Monitor (IMON) Current source which mirrors magnitude of the output current. Signal return is referenced to RS-. Current Limit (CL) Output bi-level signal. Bi-level output signal is open-collector (drain) with a 5mA sink capability and maximum voltage stand-off of 60VDC. Logic 0 : Output is in current mode control and is current limiting. Logic 1 : Normal operation. Remote Enable (ENABLE) Input bi-level signal. Bi-level input signal shall be no greater than 5VDC. Logic 0 : Output inhibited. Logic 1 : Normal operation.
Reset (RESET) Input bi-level signal. Bi-level input signal shall be no greater than 5VDC. Logic 0 : Resets fault indicators without unit shut-down. Logic 1 : Normal operation. AC Good (AC OK) Output bi-level signal. Bi-level output signal is open-collector (drain) with a 5mA sink capability and maximum voltage stand-off of 60VDC. Logic 0 : AC input below normal operating range. Logic 1 : AC input within steady-state operating range (170 to 264VAC). Voltage monitoring (VMARG) Input analog signal referenced to RS-. Adjusts output up to 4VDC higher than the nominal set point.
Features
Live insertion and removal OR-ing diodes provided on output. Voltage monitoring jacks Located on front panel. LED's (located on front panel) Power Good Power Fail AC Good Green Red Green
Protection Thermal protection - automatic shut-off for fan failure or internal overtemperature. Output Overload and Short Circuit - automatic shut-down after 30 seconds. Current regulated output down to less than 1VDC. Output Overvoltage - automatic shut-down for both main (60VDC max.) and auxiliary (15.6VDC max.) outputs. Output Undervoltage - automatic shut-down below 42VDC. Current Share Active current sharing for up to 9 AFE2000 power modules. Short Pin Short pin located in the output connector initiates shut-down of the power supply output when the power supply is removed from the host power shelf.
International Safety Standard Approvals
EN60950/IEC950 File No. E9972397 UL1950 File No. E135734
Please consult our website for the following items: Application Note http://www.artesyn.com
PAGE 2
2000W AC/DC
|
DISTRIBUTED POWER FRONT END AC/DC POWER SUPPLIES
2000 Watt AC/DC PFC front-end for distributed power architectures
PIN CONNECTIONS PIN NO. A1 A2 A3 A4 A5 A6 A7 A8 Notes
1 2 3 4 5 6 PFW signal warning issued 5 msec prior to shutdown. Chassis or safety ground. Isolated signal ground. Output ground - referenced to RS-. Refer to Application Note 106 for installation of the AFE2000 power modules into the AFS4000 power shelf. Refer to Application Note 110 for description of outputs and signals available with AFE2000 power modules installed in Artesyn standard frontend power shelf. 7 8 Class A for power module, Class B when installed in AFS4000 shelf (subject to cable/system configuration). NOTICE: Some models do not support all options. Please contact your local Artesyn representative or use the on-line model number search tool at http://www.artesyn.com/powergroup/products.htm to find a suitable alternative.
FUNCTION Short Pin AUX+ AUXRSNot Used Not Used AC OK PFW
PIN NO. B1 B2 B3 B4 B5 B6 B7 B8
FUNCTION DOWN VMARG MM I SHR RESET IMON Power Good ISO GND
(3)
PIN NO. C1 C2 C3 C4 C5 C6 C7 C8
FUNCTION RS+ RSMM F/FF/F+ INHIBIT/ENABLE CL OTW
PIN NO. D1 D2 D3 D4 D5
FUNCTION +Vout +Vout PWR RTN PWR RTN CGND
(2)
SHORT SIGNAL PIN
A8 B8 C8 A1 B1 C1
D5
D4
D3
D2
D1
AIR FLOW NORMAL
6.44 (163.58)
0.074 (1.879) 6.75 (171.45) 1.30 (33.02)
11.46 (291.08)
0.25 (6.35)
AC INPUT POWER DYNAMICS 42R08-1122 MATE - POWER DYNAMICS 43R06-2114 5.725 (145.415) 0.050 (1.270) TAPERED GUIDE PIN HOLE 0.800 (20.32)
4.23 (107.44) 4.83 (122.68) 0.0875 (2.2225)
2.063 (52.400)
0.625 (15.875)
PWR GOOD
PWR FAIL
AC GOOD
(J2) DC connector
Elcon 279-0468-00100 or equivalent.
(J1) AC connector
Power Dynamics 42R08-1122 or equivalent.
Datasheet (c) Artesyn Technologies(R) 2005 The information and specifications contained in this datasheet are believed to be correct at time of publication. However, Artesyn Technologies accepts no responsibility for consequences arising from printing errors or inaccuracies. Specifications are subject to change without notice. No rights under any patent accompany the sale of any such product(s) or information contained herein.
PAGE 3
V OUT
REF 0.475 (12.065) TAPERED GUIDE PIN HOLE 0.462 (11.735)
0.375 (9.525) MAIN DC OUTPUT/SIGNALS ELCON 279-0468-00100 MATE - ELCON 278-0468-00200
INSERTION/EJECTOR HANDLE WITH 6-32 CAPTIVE SCREW
(J2) DC mating connector
Elcon 278-0468-00200 or equivalent.
(J1) AC mating connector
Power Dynamics 43R06-2114 or equivalent.
ds_afe2000_20050824.PDF

▲Up To Search▲

Price & Availability of AFE2000-26S48NA

	To Download AFE2000-26S48NA Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .